| | Erros das Interfaces | |
| | Autor | Mensagem |
---|
alexandre.toledo
Número de Mensagens : 20 Idade : 38 Localização : Sorocaba - SP Reputação : 3 Pontos : 27 Data de inscrição : 17/09/2010
| Assunto: Erros das Interfaces Sáb maio 21, 2011 6:17 pm | |
| Alguém saberia me informar, de uma forma mais detalhada, o significado dos erros gerados pela interface serial?? . . .
Received 3637 broadcasts, 0 runts, 0 giants, 0 throttles 51 input errors, 13 CRC, 21 frame, 0 overrun, 0 ignored, 17 abort 3619551 packets output, 1942493595 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions
Obrigado | |
| | | ronaldobf Specialist
Número de Mensagens : 189 Idade : 43 Localização : São Paulo-SP Reputação : 25 Pontos : 202 Data de inscrição : 16/06/2008
| Assunto: Re: Erros das Interfaces Dom maio 22, 2011 12:59 am | |
| 51 input errors - é a somatória de todos os erros detectados nesta interface no sentido de incoming (Rx)
13 CRC - Isso nada mais é do que um controle do frame, para checar se ele chegou íntegro ao outro ponto. Baseado num algoritmo, antes do frame ser enviado para o meio, um algoritmo é rodado e gera um valor baseado neste frame. Então, este valor é informado no cabeçalho. Quando este frame chega na próxima interface, ao receber o frame, o equipamento também roda este algoritmo e gera seu valor. Então, o valor gerado é comparado com o valor que foi colocado no cabeçalho. Se forem diferentes, é sinal de que este frame sofreu alterações, isto é, não chegou da mesma forma que foi enviado. Então, ele é dropado (ignorado). Normalmente, representa problemas no meio físico, mas pode ser outros problemas também, como duplex mismatch.
21 frame - Quando detecta erro de CRC ou mesmo duplex mismatch ou colisões.
17 abort - Se não me engano, o abort é para erro de sinalização. Existe um padrão de sinalização no meio, que é controlado via camada 2. Ele é representado por sequência de 0s e 1s. Quando um frame vai ser enviado, por exemplo, ele envia uma sequencia de bits conhecida, indicando o início de uma transmissão. Quando uma sequência ilegal é detectada, a interface ignora e incrementa o abort. Isso também pode representar problemas no meio físico, já que este pode estar sofrendo de interferência ou qualquer outro problema no cabeamento.
| |
| | | ronaldobf Specialist
Número de Mensagens : 189 Idade : 43 Localização : São Paulo-SP Reputação : 25 Pontos : 202 Data de inscrição : 16/06/2008
| Assunto: Re: Erros das Interfaces Dom maio 22, 2011 1:02 am | |
| Se for um circuito (link) de dados, engaje a telco. Se for um problema entre seus equipamentos, cheque o outro lado (equipamento) e o meio físico. | |
| | | alexandre.toledo
Número de Mensagens : 20 Idade : 38 Localização : Sorocaba - SP Reputação : 3 Pontos : 27 Data de inscrição : 17/09/2010
| Assunto: Erros das Interfaces Dom maio 22, 2011 10:05 pm | |
| Obrigado Ronaldo! Achei tbm um artigo legal falando disso... valeu!
Counters
Packets input - Total number of error-free packets received. Broadcasts - Total number of broadcast or multicast packets received. Runts - Number of packets discarded because they are smaller than the medium's minimum packet size. Giants - Number of packets that are discarded because they exceed the medium's maximum packet size. Throttle - This counter indicates the number of times the input buffers of an interface have been cleaned because they have not been serviced fast enough or they are overwhelmed. Typically, an explorer storm can cause the throttles counter to increment. It's important to note that every time you have a throttle, all the packets in the input queue get dropped. This causes very slow performance and may also disrupt existing sessions. Parity - Number of parity errors on the HSSI. RX Disabled - Indicates inability to get a buffer when accessing a packet. Input Errors - Sum of all errors that prevented the receipt of datagrams. This may not balance with the sum of the enumerated output errors, because some datagrams may have more than one error and others may have errors that do not fall into any of the specific categories. CRC - Cyclic redundancy checksum generated mismatch. CRC errors also are reported when a far-end abort occurs and when the idle flag pattern is corrupted. This makes it possible to get CRC errors even when there is no data traffic. Frame - Number of packets received incorrectly having a CRC error and a noninteger number of octets. Overrun - Number of times the serial receiver hardware was unable to hand received data to a hardware buffer because the input rate exceeded the receiver's ability to handle the data. Ignored - Number of received packets ignored by the interface because the interface hardware ran low on internal buffers. Abort - Number of packets whose receipt was aborted. Bytes - Total number of bytes, including data and MAC encapsulation, transmitted by the system. Underruns - Number of times that the far-end router's transmitter has been running faster than the near-end router's receiver can handle. This may never happen (be reported) on some interfaces. Congestion Drop - Number of messages discarded because the output queue on an interface grew too long. Output Errors - Sum of all errors that prevented the final transmission. This may not balance with the sum of the enumerated output errors, because some datagrams may have more than one error and others may have errors that do not fall into any of the specific categories. Interface Resets - Number of times an interface has been completely reset. Restarts - Number of times the controller was restarted because of errors. Carrier Transitions - Number of times the carrier detect signal of a serial interface has changed state.
| |
| | | Conteúdo patrocinado
| Assunto: Re: Erros das Interfaces | |
| |
| | | | Erros das Interfaces | |
|
Tópicos semelhantes | |
|
| Permissões neste sub-fórum | Não podes responder a tópicos
| |
| |
| |